TB-V3-XX.jpg
TB-V3-XX.jpg

Perun HPA Trigger Board V3

€44.99
Only 5 available

‍ Perun HPA Trigger Board replaces mechanical contacts in your HPA system and provides lots of useful features. Magnetic and optical sensors eliminate moving parts that are prone to damage, thus increasing reliability. The elasticity of this unit gives you certainty that HPA replica made from parts made by different manufacturers will not have any incompatibility issues. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.

HPA Trigger Board works with Perun accessories for V3 gearbox, like Clicker V3.

Features:

·         Electronic safety

·         Selector sensor calibration

·         Selectable firing modes: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO

·         Adjustable trigger sensitivity

·         Rate of fire reduction

·         DMR mode

·         Programming supported with a multicolor LED diode

·         Diagnostic system

‍ Perun HPA Trigger Board replaces mechanical contacts in your HPA system and provides lots of useful features. Magnetic and optical sensors eliminate moving parts that are prone to damage, thus increasing reliability. The elasticity of this unit gives you certainty that HPA replica made from parts made by different manufacturers will not have any incompatibility issues. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.

HPA Trigger Board works with Perun accessories for V3 gearbox, like Clicker V3.

Features:

·         Electronic safety

·         Selector sensor calibration

·         Selectable firing modes: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO

·         Adjustable trigger sensitivity

·         Rate of fire reduction

·         DMR mode

·         Programming supported with a multicolor LED diode

·         Diagnostic system

Based on optical and magnetic sensors – Magnetic trigger sensors ensure that you will no longer have any problems with breaking mechanical switches from stock HPA trigger boards. Optical selector sensors can be calibrated, allowing fast installation and reliable selector operation, including detection of SAFE position and therefore ensuring reliable, electronic safe mode.

Electronic safety – Now, regardless of how sensitive the trigger might be, you can be sure there will be no accidental discharges when selector is set to “SAFE”.

Adjustable trigger sensitivity – The trigger can be set to 8 sensitivity levels for both first and second trigger stage, ranging from a very short pull needed to fire a shot, to a long one. No modification to the trigger or the gearbox is needed, and the trigger sensitivity change is possible even in the field.

Selectable firing modes – User can choose firing modes available after short or long pull of the trigger: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO.

Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.

DMR mode – Required on some fields for DMR replicas. It allows only single shots and within certain time intervals. When enabled, follow-up shots cannot be fired sooner than after 0.25 s, 0.5 s, 1 s, 2 s or 3 s, depending on chosen setting. It can also be used voluntarily for more realism - to force the shooter to not fire too fast, reflecting the effects of recoil in a real 7.62 mm rifle.

Diagnostic system - Constantly monitors the board. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.

Compatibility with Perun trigger accessories for V3 gearbox – You can use accessories like Clicker V3, just as you would with Perun AEG products.

 

Programming of all the settings is done solely by using selector and the trigger. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.

HPA Trigger Board V3 works without problems with any battery from, 7 V to 17 V.